digitize contours....

Moderator: Carlson Support

digitize contours....

Postby Jon Baker » Fri Jul 06, 2001 12:19 am

A2Ki and Survcad CES.

I just noticed that I could not digitize arcs with the DC command.. I
was able to do this in SC2k...

anyway to get this back??

--
Please scroll and read previous posts, this way you will not post the
same exact question, or look
at the AutoDesk discussion group listings for other groups.
http://support01.autodesk.com/Discussiongroups.asp

Jonathan Baker
R&R Engineers-Surveyors, Inc.
Denver, Colorado
--
Jon Baker
 

Re: digitize contours....

Postby Jon Baker » Fri Jul 06, 2001 7:51 pm

did anyone else notice this or lose theirs?

--
Please scroll and read previous posts, this way you will not post the
same exact question, or look
at the AutoDesk discussion group listings for other groups.
http://support01.autodesk.com/Discussiongroups.asp

Jonathan Baker
R&R Engineers-Surveyors, Inc.
Denver, Colorado
--
"Jon Baker" <jonathanjbaker@hotmail.com> wrote in message
news:B4A0F73FCE8FD411AF8B00207811DE59010748@WEBSERVER...
| A2Ki and Survcad CES.
|
| I just noticed that I could not digitize arcs with the DC command.. I
was able to do this in
SC2k...
|
| anyway to get this back??
|
| --
| Please scroll and read previous posts, this way you will not post the
same exact question, or look
| at the AutoDesk discussion group listings for other groups.
| http://support01.autodesk.com/Discussiongroups.asp
|
| Jonathan Baker
| R&R Engineers-Surveyors, Inc.
| Denver, Colorado
| --
Jon Baker
 

Re: digitize contours....

Postby Jason » Mon Jul 09, 2001 4:39 pm

I never noticed nor used arc in the DC command. I digitize small chords
on
arcs and go back and fill the arcs in correctly if it requires it. I do
not
attempt to eye the PC and PT of the arc, instead I basically get
multiple
points on the curve then best fit an arc through them. I tried
digitizing
arcs once before and noticed that some of them looked funny when I
overlayed
the print onto the digitized drawing, try it once and see. You never
know,
the arc may be a compound curve.

Jason

"Jon Baker" <jonathanjbaker@hotmail.com> wrote in message
news:B4A0F73FCE8FD411AF8B00207811DE5901076F@WEBSERVER...
did anyone else notice this or lose theirs?

--
Please scroll and read previous posts, this way you will not post the
same

exact question, or look
at the AutoDesk discussion group listings for other groups.
http://support01.autodesk.com/Discussiongroups.asp

Jonathan Baker
R&R Engineers-Surveyors, Inc.
Denver, Colorado
--
"Jon Baker" <jonathanjbaker@hotmail.com> wrote in message
news:B4A0F73FCE8FD411AF8B00207811DE59010748@WEBSERVER...
| A2Ki and Survcad CES.
|
| I just noticed that I could not digitize arcs with the DC command..
I

was able to do this in
SC2k...
|
| anyway to get this back??
|
| --
| Please scroll and read previous posts, this way you will not post
the

same exact question, or look
| at the AutoDesk discussion group listings for other groups.
| http://support01.autodesk.com/Discussiongroups.asp
|
| Jonathan Baker
| R&R Engineers-Surveyors, Inc.
| Denver, Colorado
| --
Jason
 


Return to Survey

Who is online

Users browsing this forum: No registered users